Wide Area Networks

1.	When setting up Frame Relay for point-to-point subinterfaces, which of the following must not be configured?
	A. The Frame Relay encapsulation on the physical interface B. The local DLCI on each subinterface C. An IP address on the physical interface D. The subinterface type as point-to-point

2.	Which command will display the CHAP authentication process as it occurs between two routers in the network?
	A. show chap authentication B. show interface serial 0 C. debug ppp authentication D. debug chap authentication

3.	The Acme Corporation is implementing dial-up services to enable remote-office employees to connect to the local network. The company uses multiple routed protocols, needs authentication of users connecting to the network, and since some calls will be long distance, needs callback support. Which of the following protocols is the best choice for these remote services?
	A. 802.1 B. Frame Relay C. HDLC D. PPP E. PAP

4.	You need to configure a router for a Frame Relay connection to a non-Cisco router. Which of the following commands will prepare the WAN interface of the router for this connection?
	A. Router(config-if)#encapsulation frame-relay q933a B. Router(config-if)#encapsulation frame-relay ansi C. Router(config-if)#encapsulation frame-relay ietf D. Router(config-if)#encapsulation frame-relay cisco

5.	Which WAN encapsulations can be configured on an asynchronous serial connection? PPP ATM HDLC SDLC Frame Relay
	A. 1 and 2 B. 2 and 4 C. 3, 4 and 5 D. All of the above

IPv6

1.

Which of the following is true when describing a multicast address?

A. Packets addressed to a unicast address are delivered to a single interface. B. Packets are delivered to all interfaces identified by the address. This is also called a one-to-many address. C. Identifies multiple interfaces and is only delivered to one address. This address can also be called one-to-one-of-many. D. These addresses are meant for nonrouting purposes, but they are almost globally unique so it is unlikely they will have an address overlap.

2.

Which of the following is true when describing a unicast address?

A. Packets addressed to a unicast address are delivered to a single interface. B. These are your typical publicly routable addresses, just like a regular publicly routable address in IPv4. C. These are like private addresses in IPv4 in that they are not meant to be routed. D. These addresses are meant for nonrouting purposes, but they are almost globally unique so it is unlikely they will have an address overlap.

3.	To enable OSPFv3, which of the following would you use?
	A. Router1(config-if)# ipv6 ospf 10 area 0.0.0.0 B. Router1(config-if)# ipv6 router rip 1 C. Router1(config)# ipv6 router eigrp 10 D. Router1(config-rtr)# no shutdown E. Router1(config-if)# ipv6 eigrp 10

4.	What multicast addresses does RIPng use?
	A. FF02::A B. FF02::9 C. FF02::5 D. FF02::6

5.	Which statement(s) about IPv6 addresses are true? Leading zeros are required. Two colons (::) are used to represent successive hexadecimal fields of zeros. Two colons (::) are used to separate fields. A single interface will have multiple IPv6 addresses of different types.
	A. 1 and 3 B. 2 and 4 C. 1, 3 and 4 D. All of the above

Wireless Technologies

1.	What is the frequency range of the IEEE 802.11a standard?
	A. 2.4Gbps B. 5Gbps C. 2.4GHz D. 5GHz

2.	What is the maximum distance running the lowest data rate for 802.11b?
	A. About 100 feet B. About 175 feet C. About 300 feet D. About 350 feet

3.	What is the maximum distance with maximum data rate for 802.11a?
	A. About 65-75 feet B. About 90-100 feet C. About 150 feet D. Over 200 feet

4.	What is the frequency range of the IEEE 802.11b standard?
	A. 2.4Gbps B. 5Gbps C. 2.4GHz D. 5GHz

5.	You have a Cisco mesh network. What protocol allows multiple APs to connect with many redundant connections between nodes?
	A. LWAPP B. AWPP C. STP D. IEEE

Network Address Translation

1.	Which command would you place on interface connected to the Internet?
	A. ip nat inside B. ip nat outside C. ip outside global D. ip inside local

2.	Which command will show you all the translations active on your router?
	A. show ip nat translations B. show ip nat statistics C. debug ip nat D. clear ip nat translations *

3.	Which command would you place on interface on a private network?
	A. ip nat inside B. ip nat outside C. ip outside global D. ip inside local

4.	Pat Address Translation is also termed what?
	A. NAT Fast B. NAT Static C. NAT Overload D. Overloading Static

5.	When creating a pool of global addresses, which of the following can be used instead of the netmask command?
	A. / (slash notation) B. prefix-length C. no mask D. block-size

Security

1.	Which of the following is true regarding access lists applied to an interface?
	A. You can place as many access lists as you want on any interface until you run out of memory. B. You can apply only one access list on any interface. C. One access list may be configured, per direction, for each layer 3 protocol configured on an interface. D. You can apply two access lists to any interface.

2.	Which command would you use to apply an access list to a router interface?
	A. ip access-list 101 out B. access-list ip 101 in C. ip access-group 101 in D. access-group ip 101 in

3.	Which of the following is an example of a standard IP access list?
	A. access-list 110 permit host 1.1.1.1 B. access-list 1 deny 172.16.10.1 0.0.0.0 C. access-list 1 permit 172.16.10.1 255.255.0.0 D. access-list standard 1.1.1.1

4.	You need to create an access list that will prevent hosts in the network range of 192.168.160.0 to 192.168.191.0. Which of the following lists will you use?
	A. access-list 10 deny 192.168.160.0 255.255.224.0 B. access-list 10 deny 192.168.160.0 0.0.191.255 C. access-list 10 deny 192.168.160.0 0.0.31.255 D. access-list 10 deny 192.168.0.0 0.0.31.255

5.	You are working on a router that has established privilege levels that restrict access to certain functions. You discover that you are not able to execute the commandshow running-configuration. How can you view and confirm the access lists that have been applied to the Ethernet 0 interface on your router?
	A. show access-lists B. show interface Ethernet 0 C. show ip access-lists D. show ip interface Ethernet 0

Virtual LANs

1.	Which of the following is true regarding VLANs?
	A. You must have at least two VLANs defined in every Cisco switched network. B. All VLANs are configured at the fastest switch and, by default, propagate this information to all other switches. C. You should not have more than 10 switches in the same VTP domain. D. VTP is used to send VLAN information to switches in a configured VTP domain.

2.	Which protocol reduces administrative overhead in a switched network by allowing the configuration of a new VLAN to be distributed to all the switches in a domain?
	A. STP B. VTP C. DHCP D. ISL

3.	Which of the following is true regarding VTP?
	A. All switches are VTP servers by default. B. All switches are VTP transparent by default. C. VTP is on by default with a domain name of Cisco on all Cisco switches. D. All switches are VTP clients by default.

4.	Which of the following commands sets a trunk port on a 2960 switch?
	A. trunk on B. trunk all C. switchport trunk on D. switchport mode trunk

5.	Which command will configure a switch port to use the IEEE standard method of inserting VLAN membership information into Ethernet frames?
	A. Switch(config)# switchport trunk encapsulation isl B. Switch(config)# switchport trunk encapsulation ietf C. Switch(config)# switchport trunk encapsulation dot1q D. Switch(config-if)# switchport trunk encapsulation isl E. Switch(config-if)# switchport trunk encapsulation dot1q